Difference angle quantization index modulation scheme for image watermarking

In this paper, we propose a new angle quantization index modulation (AQIM) method, called the difference AQIM (DAQIM) method. The proposed method aims to improve the watermarking performance against gain attacks. Unlike the original AQIM method (Ourique et al., Angle QIM: a novel watermark embedding scheme robust against amplitude scaling distortions, in: Proceedings of IEEE International Conference on Acoustics, Speech, and Signal Processing, vol. 2, 2005, pp. 797–800), the DAQIM method quantizes the difference of the two angles instead of the angles themselves. The main advantage of the DAQIM method is to disperse the interference to the watermark signal from one angle to more angles. Thus, the watermark has a higher ability to resist attacks. We perform a theoretical analysis of the document-to-watermark ratio (DWR) based on our proposed method. We show that our proposed method can obtain a lower embedding distortion compared to the AQIM and the gradient direction watermarking (GDWM) (Nezhadarya et al., IEEE Trans. Inf. Forensics Secur., 6(4), 2011, 1200–1213), methods under the same robustness and payload conditions. The experimental results demonstrate that our proposed method outperforms common existing methods in terms of the robustness against various attacks such as the JPEG quantization noise, additive white Gaussian noise (AWGN), cropping effect and mean filtering.     

Direct strain evaluation method for laboratory-based pillar performance

Pillar stability is one of important aspects for underground mines.Generally,the stability of the pillars is evaluated empirically based on case studies and site-specific rock mass conditions in mines.Nevertheless the empirical approach applicability can sometimes be constrained.The numerical-based approaches are potentially more useful as parametric studies can be undertaken and,if calibrated,can be more representative.Both empirical and numerical approaches are dependent on the strength evaluation of the pillars while the strain developing in the pillars is seldom taken into consideration.In this paper,gypsum and sandstone samples were tested in laboratory with different width-to-height ratios(W/H)to adapt the strain evaluation method to the laboratory-based pillars.A correlation was then developed between the strain and the width-to-height ratio for pillar monitoring purposes.Based on the results,a flowchart was created to conduct back analysis for the existing pillars to evaluate their stability and design new pillars,considering the strain analysis of the existing pillars with the W/H ratios modelled.     

Adaptive GLR-, Rao- and Wald-based CFAR detectors for a subspace signal embedded in structured Gaussian interference

The problem of detecting a subspace signal embedded in subspace Gaussian interference and thermal noise is studied in this paper. In this problem, both the signal-independent and signal-dependent interferences are assumed to be present, therefore the overall interference subspace covers the signal subspace. The approach of this paper extends previous works involving either of those two kinds of interferences. A set of secondary data containing only interference plus noise is employed to estimate the interference covariance matrix and the noise power. Three new detectors are designed via the generalized likelihood ratio (GLR), Rao and Wald tests, respectively. Their probabilities of false alarms (PFAs) and detections are analytically derived. The PFAs show that the new detectors have the constant false alarm rate (CFAR) property against the interference and noise. Numerical results show that the new detectors outperform their counterparts for the studied problem. Furthermore, the new detectors are less sensitive to the secondary data size and to the mismatched subspace signal than some other detectors, such as the GLR detector (GLRD), the adaptive matched filter (AMF), the adaptive subspace detector (ASD), etc.     

面向文本数据的正则化交叉验证方法

面向文本数据建模时,交叉验证方法是特征选择及模型比较任务中的常用方法。许多研究表明,文本数据模型的性能估计对交叉验证的数据切分方式较为敏感,不合理的切分方式可能会导致不稳定的性能估计值,使得实验结果可复现性差。该文试图论证基于多次重复(m次)的2折交叉验证,通过引入对训练集、验证集分布差异的约束,所构造的正则化m×2交叉验证方法(简记为m×2 BCV)可以改善模型的性能指标的估计,适宜于模型比较。该文首先针对文本数据引入训练集与验证集分布差异的卡方度量,基于该度量构建数据切分的正则化条件,以最大化模型性能指标的信噪比为目标,给出了满足正则化条件的m×2 BCV的数据切分优化算法。最后,以自然语言处理中汉语框架语义角色标注任务为例,验证了基于m×2 BCV方法的有效性。     

少量有机碳对单级自养脱氮工艺性能的影响

采用序批式生物膜反应器(SBBR),经过4个阶段的培养,快速富集好氧氨氧化细菌(AOB)和厌氧氨氧化细菌(AnAOB),并考察不同低碳氮比对工艺脱氮性能的影响。结果表明,NH4^+-N去除率可达到99%以上,TN去除率可达到90%以上。对应C/N=0、1和2时,反应器出水NH4^+-N和TN去除率分别为99.59%、99.5%、98.47%和93.75%、97.22%、98.11%。说明少量COD的存在,可实现同步硝化-厌氧氨氧化-反硝化,且在一定程度上提高脱氮效率。     

超生雾化降尘研究及应用

为解决某矿破碎筛分车间粉尘污染问题，采用喷嘴雾化理论设计喷嘴雾化降尘实验，并根据实验结果在该矿破碎筛分车间应用了超声雾化降尘技术。实验及应用结果表明：超声雾化发生器的液体雾化装置，气体辅助雾化装置和雾束形成器的几何结构影响喷雾的雾化参数与流量特性，液体雾化器与气体辅助雾化装置影响液体初次破碎与雾化，雾束形成器影响雾滴的二次破碎与约束液束形态；超声雾化发生器的气液比与气液压力比存在幂函数关系，幂指数为-1.09；雾滴粒径越小，雾滴的降尘效率越高，当雾滴D50为23 μm时，雾滴的降尘效率在94%以上；在破碎筛分车间振动筛给料皮带和筛上皮带受料点布置超声雾化发生器，超声雾化发生器开启后，车间内粉尘浓度降低至586～10.54 mg/m3，降尘效率在71.38%以上。     

Effect of Reynolds number and boundary layer thickness on the performance of V-cone flowmeter using CFD

The effect of Reynolds number and boundary layer thickness on the performance of V-cone flowmeter has been evaluated using computational fluid dynamics (CFD). The shear stress transport k-ω (SST k-ω) turbulence model has been adopted for closure. The performance of two V-cone flowmeters with different beta ratios (β) viz., 0.6 and 0.7 for a fixed vertex angle (ϕ) of 60° has been analysed as a function of Reynolds number (Re). The results show that the coefficient of discharge (C_d) increases with Reynolds number in the laminar and transition flow regimes whereas it is nearly constant in turbulent flow regime. From the results, it can be concluded that C_d is independent of Re for values equal to 4000 and beyond. Further, it is also seen that the performance of the V-cone flowmeter is not affected by the upstream boundary layer thickness if the velocity profiles having different boundary layer thickness are extracted from an axial distance of 10D and more are fed at 5D upstream of the meter. However, the meter is sensitive to the extracted velocity profile from an axial distance of 5D and uniform velocity profile being fed at 5D upstream. The value of C_d may be sensitive as a result of the pressure variation due to the obstruction.     

一种轻小型四极杆质谱仪射频电源的研制

四极杆结构是四极杆质谱仪的核心结构，由射频电源分别施加两组高压高频信号进行驱动，利用电场的变化和输入离子的质荷比差异对离子进行筛选。针对四极杆质谱仪小型化的研制需求，以信号调制模块、放大模块、反馈电路和直流模块为基本构型，设计了一种应用于轻小型四极杆质谱仪的射频驱动电源。经实际测试，该电源可以在谐振频率1.33 MHz、扫描频率10 Hz的输入条件下，输出峰 峰值电压最高可达3.33 kV的调幅射频高压信号并驱动四极杆结构，扫描切换时间不高于1 ms。射频电源输出信号稳定、波动小、交直比的波动为0.1%。该射频电源相较于常规的四极杆射频电源具有更高的扫描范围，体积小巧，功耗仅30 W，接口简单，有较高的实用价值。     

小尺度交通信号灯的检测与状态识别

交通信号灯识别包括检测和状态识别，在智能交通系统中发挥重要作用。基于YOLOv3算法提出了一种交通信号灯检测与状态识别模型。针对交通信号灯相较于交通场景中其他目标具有尺度小的特性进行了算法的设计：降低骨干网络的下采样倍率以增加小尺度目标的特征描述能力；通过增大特征图的尺度来改进多尺度特征融合；引入广义交并比作为检测任务的损失函数来改进目标边界框的回归效果。同时，根据交通信号灯本身的特性，使用颜色和形状约束的方法对信号灯进行状态识别和类别验证。最后在公开的Bosch交通信号灯数据集上和实际的城区道路进行了实验验证。实验结果表明，所提出的算法能够提升交通信号灯识别的精度和召回率，识别准确率可以达到90%左右。     

剂油比对煤焦油沥青质加氢过程的影响

以中低温煤焦油沥青质为原料,采用NiMoW/γ-Al_2O_3商业催化剂,在反应温度380℃、反应压力8 MPa和反应时间1.5 h条件下,分别在不同剂油质量比(1∶25、1∶20、1∶15、1∶10)条件下进行加氢实验,通过采用元素分析、FT-IR、XRD、~1H-NMR和XPS等分析表征手段,考察不同剂油质量比对中低温煤焦油沥青质加氢转化过程的影响。结果表明,随着剂油质量比的增加,沥青质转化率提高,加氢产物分布也发生大幅变化,沥青质和芳香分轻质化转化为饱和分。但随着剂油质量比的进一步提高,同时也发生了更多的裂化反应和缩合反应,剂油质量比在合适范围能够很好地起到加氢轻质化且抑制结焦的效果。